Home > Audi A4 > Audi A4 Power Seat Not Working

Audi A4 Power Seat Not Working

Contents

Only after I removed the seat modules. therefore, the switches must be working to some degree. I will do that tomorrow after I pull the old one and wd-40 all the plugs and see if that helps. They clip on just as you said and this is a 2004. this content

Newer Than: Useful Searches Recent Posts More... A green/white, a black/white and a black wire. Remember, my seats are stuck back. XenForo add-ons by Waindigo™ ©2015 Waindigo Ltd.

Audi Power Seat Issues

I really believe the comfort module is going to provide a fix to some of these problems. top module. Be careful with them as they can destroy control modules unless they specifically say high impedance on the back. If you don't have it, I may purchase alldata for this car again..I had it, but it sucked so bad I got a refund.

Also, please tell me how to get those plugs loose! The front piece of the button moves up/down the front side of the seat and the back piece of the button moves up/down back side of the seat. This will take you no more than 10 minutes. __________________ AudiWorld || 1999 A6 2.8q | 1992 100CS | AudiWorld Photo Gallery Links || Stoney's FAQ | CycleForums European Sportbikes Forum Audi A4 Electric Seat Motor Once this is done you should notice the difference as before with the seat bent forwards the rails were not moveable but now they should slide forward and backwards with ease,

I have to know if that module is bad or something else is causing it. Audi A4 Seat Not Moving Finally! Second, the abs code is normal after disconnecting the battery and the code will clear itself after you drive it the first time (roughly 100ft.). http://www.audiworld.com/forums/a6-s6-c5-platform-discussion-7/electric-seat-will-not-move-forward-1704142/ Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if you need to. 100% Satisfaction Guarantee Rate the answer you receive.

On the inboard side of the seat, about half way up, you'll see a cylinder shaped motor with a rectangular like attachment point at the rear. Audi A4 Seat Repair These were the only two that had roof in the title. I installed the new modules, and I hear the relays clicking but still no movement on either seat and I get a code fault that says 02005 code pin fault, on I would if I knew how.

Audi A4 Seat Not Moving

Oturum aç Çeviri Yazısı İstatistikler 15.608 görüntüleme 22 Bu videoyu beğendiniz mi? Now the tool is locked into position, if your top is having the problem I think it is then you should just have to turn the whole tool clockwise about 1/8 Audi Power Seat Issues So your input into the vag-com would be 03710.Sincerely,George RS4 Tech and other Audi Specialists are ready to help you Ask your own question now Customer: replied6 years ago. Audi A4 Passenger Seat Stuck I need to know if "E" is also on the list.

Where to go from here? news Also, judging from your last post it sounds as if you are using an old meter. Since there is no noise from the worm gears or the motor I think the problem is with the up and dowin positions of the switch .Can anybody guide me how But, if the control contactor wasn't powered, the motor windings would read open. Audi A4 Seat Adjustment

I'm in the coding area of vag com now. Especially when this is nearly impossible to get to without seat removal. I just want to swap the position of the wire going to the motor. have a peek at these guys ECS Tuning 53.695 görüntüleme 2:44 Audi A4 FrontSeat Removal - Süre: 2:19.

Wow, the seatback switch is likely the problem. Audi A4 Electric Seat Fuse There are two incline motors and the one incline closest to exterior doors wasn't working on either side but those you can put a square bit in the end and take Here is the copy of the fault:Tuesday,05,October,2010,13:19:40:01676VCDS Version: Release 10.6.1 (x64) Address 63: Entry Assist,D Labels: NoneControl Module Part Number: 8H0 959 760 A Component and/or Version: EasyEntry F H12 X024

Tell me what to do next.

alright, I figured out the coding pin problem. Thanks.

UPDATE: I readon a forum that the E is just a later model of the C on the convenience module but I would like you to look that up for I scanned the auto roof, no problems. Audi A6 Power Seat Fuse When you replace it you will have to re-code it.

We'd really appreciate it! thanks.john Customer: replied6 years ago. That changed the magnets position and now i got normal working motor. check my blog I am sorry, I thought we were talking about the passenger seat all along.

Your 5th digit is a zero, i forgot to mention that. I would start by replacing the module as that is what is known as a master module. I replaced all my control arms 3 months ago too Current: E46 ///M3 Convertible Past: 2004 Audi A4 1.8TQM: KW-APR-OEM+, 2003 Audi A4 3.0 Reply With Quote 01-03-201008:47 PM #9 Video kiralandığında oy verilebilir.

But roof electronics will not respond. Here is why: When you take an ohm meter and unplug a motor and check the motor terminals on an Rx1 setting for the meter, you should get a measurable amount Performance Mods: 20" Euro RS7 Blade titanium Wheels w/ Black Audi caps, and wrapped in 265/35/20 Pirelli P Zeros, Eibach Pro-Springs, S7 Sport Exhaust "Black Tips", APR Stage II. Thanks again. Customer: replied6 years ago.

Audi USA 34.327 görüntüleme 1:33 Daha fazla öneri yükleniyor... When the front releases, it raises up and stays there. According to the parts film C does supersedes to E Ask Your Own Audi Question Customer: replied6 years ago. Yes I checked the fuses.

Chris Kwok Abone olAbone olunduAbonelikten çık22 Yükleniyor...